Free Cisco 350-501 Exam Questions

Become Cisco Certified with updated 350-501 exam questions and correct answers

Page: 1 / 92

Total 460 Questions | Updated On: Nov 14, 2024

Add To Cart

Question 1

Refer to the exhibit. A network engineer is configuring router RB to secure BGP advertisements against route hijacking activity. RB must validate all prefixes that it receives from origin AS 200 before installing them in the BGP route table. Which configuration meets the requirement?

A : RB(config)# router bgp 100RB(config-router)# address-family ipv4 unicastRB(config-router-af)# bgp bestpath origin-as use validity

B : (config-bgp)# router bgp 100RB(config-bgp)# bgp origin-as validation signal ibgpRB(config-bgp)# bgp bestpath origin-as allow invalid

C : RB(config-bgp)# router bgp 100RB(config-bgp)# bgp origin-as validation time off

D : RB(config)# router bgp 100RB(config-router)# address-family ipv4 unicastPB(config-router-af)# bgp origin-as validation enable

Answer: D

Question 2

Refer to the exhibit:

After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP.
Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)

A : bel 0 is used for the prefix displayed but will not be part of the MPLS label stack for packets destined for 192 168.10.10.

B : timate Hop Popping is in use for the prefix displayed.

C : bel 0 is used for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10

D : nultimate Hop Popping is in use for the prefix displayed

E : bel 3 is in use for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10

Answer: A,D

Question 3

Refer to the exhibit. Router R1 is configured with class map CE with match Ip precedence critical to align

with customer contract SLAs. The customer is sending all traffic from CE1 toward the FTP server with IP

precedence 5 A network engineer must allow 10% of interface capacity on router R3 Which two actions must

the engineer take to accomplish the task? (Choose two )

A : lmptem4Dt4M$§ map on R1 to match all packets with QoS IP precedence value 100.

B : Implement a class map on R3 to match all packets with QoS IP precedence value 101.

C : Apply a policy map to R1 to reserve the remaining 10% of interface bandwidth.

D : Apply a policy map to R3 to reserve 10% of interface bandwidth.

E : Implement a class map on R3 to match all packets with QoS IP precedence.

Answer: B,D

Question 4

Refer to the exhibit:

Which statement about this configuration is true"?

A : requires an explicit Cisco MPLS TE path to be configured for the tunnel to run

B : requires OSPF to also be running to have optimized Cisco MPLS TE tunnels

C : requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run

D : is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing

Answer: D

Question 5

A network engineer is configuring Flexible NetFlow and enters these commands

What are two results of implementing this feature instead of traditional NetFlow? (Choose two.)

A : U and memory utilization are reduced.

B : ly the flows of top 100 talkers are exported.

C : data export flow is more secure

D : number of packets to be analyzed are reduced.

E : accuracy of the data to be analyzed is improved.

Answer: A,D

Page: 1 / 92

Total 460 Questions | Updated On: Nov 14, 2024

Add To Cart